産品展示
分類
泉州聯進機械有限公司
QUANZHOU LIANJIN MACHINE CO., LTD
冰
水
使
說
明
Cooling M
水管安裝示意圖 Installation schemes
用途：用于給水槽的水進行降溫。
特點：根據水槽水質含防粘劑化工産品腐蝕性高的弊病，采用純钛管蒸發器，熱傳遞好耐腐蝕，改進了傳統的銅管蒸發器缺點。
公共設備電力：電壓380V,50Hz。
①管道泵：2.2kw 兩台
②冷卻塔：15噸
④主電源線：10平方 四芯線
主要技術參數 Technical Parameters | |
LJ-15HP | |
15HP | |
1400*850*1450 | |
功率Power (KW) | |
重量 | 400 |
上班：開機順序：提前十分鍾開機
1. 閉合冰水循環泵
2. 閉合熱水循環泵
3. 再閉壓縮機循環泵
下班：随時斷電順序：
1. 斷開壓縮機
斷開冰水泵
2. 機台維修前請參考以上的正常值，維修前要清洗幹淨外觀和油漬的位置，便于電工機修工維修人員的操作。
維修保養 Maintenance
保養定爲三個月清洗冷卻塔一次，十天至十五天更換水槽内的水，（以免影響材質）三個月軸承注油，免幹燥損壞，移位。
常見小問題
●冰水循環：進料的噴水管出水量小
原因：1.水槽吸水口粗過濾網賭了碎膠料。
2.管道過濾器的不鏽鋼濾網堵塞
清洗方法：務必停機水泵，取出濾網清洗幹淨。裝好方可開機。
●熱水循環：手摸冷卻塔的水溫感覺比常溫高。原因：冷卻塔高溫狀态易産生污垢，循環水量不夠，散熱管道不通暢。
2. 6-8小時。
3. 打開冷凝端蓋，用焊在鋼筋上鐵刷子刷通管道。
4. 切記:需換清水三次，方可正常使用避免除垢劑腐蝕水泵元件及制冷管道。
●高壓跳: 1. 冷卻塔污垢積太多，冷卻塔噴水轉盤堵塞不轉等。
2. 水泵壞。冷卻塔風機不轉。
3. 冷凝管道污垢機過多。
4. 葉輪堵塞，不自動補水等以上原因引起流動不夠，水壓太小而跳。
5. 冷卻塔配套不對，如十匹應配十噸冷卻塔。
6. 制冷劑注入量過多或更換部件時沒有經嚴格真空，系統含有空氣。
3. 冷媒通道微堵不順口，如過濾器進出有溫差，手閥進出有溫差。
4. 冰水泵配置不夠功率。
少見故障 Rare fault
壓縮機不工作：1. 冰水泵正常運轉否。
2. 熱水器正常運轉否。
3. 冰水熱水泵均正常方能啓動壓縮機。
4. 檢查空氣開關，接觸器，繼電器，壓力開關，溫控器等電路由專業電工檢修。
細濾 fine filter 粗濾 coarse filter開關 switch 噴水管 spray pipe球閥開關 ball valve switch此不可裝開關 Don’t fix switch here.
Advantage: According to the water quality of the flume contains anti - adhesive chemical products corrosion high disease，Pure titanium tube evaporator，Good heat transfer corrosion resistance，The shortcomings of traditional copper tube evaporator are improved.
CoolingachineInstallation instructions
Public equipment：Power: 380V,50Hz.
●①Pipe pump:2.2kw two sets.
②Cooling tower: 15tons
③Plastic pipe(1.5inches)to water pipe（0.4 inches）
④ Host power line: 10 mm²four-core
主要技術參數 | |
型号 Model | |
機型Systems | 15 |
外型尺寸 | 1400*850*1450 |
功率Power (KW) | 11 |
400 |
●Start work: the steps of start-up: start up in ten minutes
1. Close the ice water circulation
2. Close the hot water circulation pump
3. Close compressor circulation pump
●After work: the steps of end power at any time:
2. Disconnect hot water circulation pump
●Hand over:1.We should record the data as follow: the normal value of high-low pressure (kilograms),The setting value of high-low pressure controller (kilograms),The running current (amperes),The setting value of protection (amperes)
2. Please refer to the above normal values before the machine maintenance, clean cover and the position of oil in order to be convenient for repairman to operate.
3. Air switch can’t be change to a bigger one, in case of burning compressor.
Clean cooling tower at every three monthes, change the sink’s water at every ten days to fifteen days, (so as not to affect the material) infuse the oil into bearing at every three monthes, avoid dry damage, shift.
FAQ
of the water sucking mouth of sink is thicker than dust gauze.
Reason: The cooling tower is easy to produce dirt at high temperature, circulation water is not enough, heat pipe is obstructed.
2. Add water and appropriate cleaner, open cycle pump running softening for 6-8 hours.
3. Open the cover of condensation, brush the pipeline by iron brush on steel bar.
4. Remember: change clear water three times to avid that cleaner corrode pump components and refrigeration pipeline corrosion.
1. The cooling tower has too much dirt, the water spray of the cooling tower is jamed and not work.
3. Condensation pipes have too much dirt.
4.Impeller congestion, not to be automatic to fill water etc, these reasons cause the water flow is not enough, and water pressure is too small to lead to jump.
5. Cooling tower is in supporting the wrong horse, such as ten horse should match ten tons of cooling tower.
6. The injection quantity of refrigerants is too much or when replace parts without the strict vacuum, containing the air in the system.
●Low pressure jump
2. Refrigerants lead to the static is not to have five kilograms.
3. Cold channels micro plug, such as filters have different temperature in into and out of.
4. Ice water pump configuration doesn’t reach enough power.
Rare glitches
Compressor doesn’t work:
3. he compressor can only be started after the ice water pump and hot water pump surely work normally.
4. Check air switch, contactor, relay, pressure switch, the thermostat and other circuits are checked and repaired by professional electricians.
泉州聯進機械有限公司 京ICP證000000号
泉州聯進機械有限公司
技術支持：廈門易爾通網絡科技有限公司泉州分公司 信息支持：東南商機網
京ICP證000000号